Role of In-Situ Testing in Geotechnical Earthquake Engineering

The available in situ testing techniques of special relevance in Geotechnical Earthquake Engineering are subject to a synthetic review in the light of the general framework of soil stress-strain behavior. Especial attention is devoted to the recent innovations and current capabilities of in situ testing methods to assess the shear modulus G and damping ratio D. The determination of the undrained steady state shear strength via penetration and seismic tests is also discussed

Impact of debris flows on filter barriers: Analysis based on site monitoring data

Debris flows are one of the most complex and devastating natural phenomena, and they affect mountainous areas throughout the world. Structural measures are currently adopted to mitigate the related hazard in urbanized areas. However, their design requires an estimate of the impact force, which is an open issue. The numerous formulae proposed in the literature require the assignment of empirical coefficients and an evaluation of the kinematic characteristics of the incoming flow. Both are generally not known a priori. In this article, we present the Grand Valey torrent site (Italian Alps). A monitoring system made up of strain gauges was installed on a filter barrier at the site, allowing the evaluation of impact forces. The system provides pivotal information for calibrating impact formulae. Two debris flows occurred during the monitoring period. We present the interpretation of videos, impact measurements, and the results of numerical analyses. The combined analysis allows a back calculation of the events in terms of forces, flow depth, and velocity. Thus, we investigate the applicability of the impact formulae suggested in the literature and of the recommended empirical coefficients. The results highlight that hydrostatic effects dominated the impact during the first event, while hydrodynamic effects prevailed in the second one

Snow Avalanche Impact Measurements at the Seehore Test Site in Aosta Valley (NW Italian Alps)

In full-scale snow avalanche test sites, structures such as pylons, plates, or dams have been used to measure impact forces and pressures from avalanches. Impact pressures are of extreme importance when dealing with issues such as hazard mapping and the design of buildings exposed to avalanches. In this paper, we present the force measurements recorded for five selected avalanches that occurred at the Seehore test site in Aosta Valley (NW Italian Alps). The five avalanches were small to medium-sized and cover a wide range in terms of snow characteristics and flow dynamics. Our aim was to analyze the force and pressure measurements with respect to the avalanche characteristics. We measured pressures in the range of 2 to 30 kPa. Though without exhaustive measurements of the avalanche flows, we found indications of different flow regimes. For example, we could appreciate some differences in the vertical profile of the pressures recorded for wet dense avalanches and powder ones. Being aware of the fact that more complete measurements are necessary to fully describe the avalanche flows, we think that the data of the five avalanches triggered at the Seehore test site might add some useful information to the ongoing scientific discussion on avalanche flow regimes and impact pressure

A new experimental snow avalanche test site at Seehore peak in Aosta Valley (NW Italian Alps) - Part II: Engineering aspects

The estimate of the effects produced by the impact of a snow avalanche against an obstacle is of the utmost importance in designing safe mountain constructions. For this purpose, an ad-hoc instrumented obstacle was designed and built in order to measure impact forces of small and medium snow avalanches at Seehore peak (NW Italian Alps). The structural design had to consider several specific and unusual demands dictated by the difficult environment. In this article, the new test facility is described from the engineering point of view, discussing the most important aspects of the analyzed problems which were solved before and after the construction. The performance of the instrumented obstacle in the first two operating seasons, and some proposals for future upgrading are eventually illustrate

An apparatus for in-situ direct shear tests on snow

The article presents a prototype of a new device for measuring the shear strength of snow specimens in situ. The resistance to sliding of a snow slab on a mountain slope is a key parameter in snow mechanics. The proposed apparatus acts as a sampler, to obtain a nearly undisturbed specimen, and as a shear box, similar to those used in the laboratory, with complete control of the test procedure. The main components of the device are a pneumatic system, for the application of normal and shear forces to the specimen, a real-time controller for commanding and recording of the data, and a computer. The apparatus can be carried to the place of the experiments and operated by a team of two researchers. Calibration and preliminary tests are also described in the article